Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Jaeger

Pages: 1 [2] 3 4 ... 7
16
Classifieds / Re: Deans smart charger for sale or trade
« on: December 31, 2013, 07:51:32 PM »
Lock it down

17
Classifieds / Re: Deans smart charger for sale or trade
« on: December 26, 2013, 10:03:38 PM »
Will trade for lipo charger!

18
Classifieds / Stripped upper an lower with motor grip
« on: December 25, 2013, 08:22:10 PM »
I have a polymer G&G PWS Diablo stripped upper and lower with tan stippled motor grip. This is ONLY THE BODY. No mag release, no charging handle, and nothing else.

19
Classifieds / Deans smart charger for sale or trade
« on: December 25, 2013, 08:12:15 PM »
I have a deans smart charger for sale for $15 or trade. Just make me offer. Contact me a zboyjason@yahoo.com

20
DIY / Re: Kwa kp45
« on: December 23, 2013, 04:30:08 PM »
True, I have to go up there sometime and find out how much one will cost

21
DIY / Re: Kwa kp45
« on: December 23, 2013, 04:05:24 PM »
But I'm the only person that I know of that uses a usp

22
DIY / Kwa kp45
« on: December 21, 2013, 04:33:20 PM »
I'm trying to find the measurements for the kwa kp45 trigger. I need them so I can machine my own out of steel but I made the mistake of melting then old one after it broke. Does anyone know where I can find the dimensions?

23
Classifieds / Re: I'm looking for a good motor
« on: December 21, 2013, 12:05:49 PM »
I'm going to get the lonex ultra torque gear set.

24
Classifieds / Re: I'm looking for a good motor
« on: December 20, 2013, 11:44:43 PM »
What would you want for it? I'm in the middle of getting new gears now and I can get a new piston easily.

25
Classifieds / I'm looking for a good motor
« on: December 20, 2013, 02:59:53 PM »
I need a good motor that is better than my stock G&G motor. I have a G&G polymor body I can trade

26
DIY / Re: M4 shooing problems AGAIN!!! And Magpul PTS pmags problems
« on: December 19, 2013, 12:48:39 PM »
Very true Metal. But I got them as a gift and since I tool the top of the follower off it works great

27
DIY / Re: M4 shooing problems AGAIN!!! And Magpul PTS pmags problems
« on: December 19, 2013, 10:00:41 AM »
Two cents I better than I sence

28
DIY / Re: M4 shooing problems AGAIN!!! And Magpul PTS pmags problems
« on: December 19, 2013, 06:47:41 AM »
I have one beta and 3 PTS mags

29
DIY / Re: M4 shooing problems AGAIN!!! And Magpul PTS pmags problems
« on: December 19, 2013, 12:13:45 AM »
I just found out it was the two piece follower, I only put in 30 rounds to test them. They have a 2 piece follower that pivets and you have to take to top part if the follower off because the top piece is smaller than a bb and the  bb will get stuck between the followers and the mag walls causing a jam. I found this out about an hour after posting the question abou them

30
DIY / M4 shooing problems AGAIN!!! And Magpul PTS pmags problems
« on: December 18, 2013, 10:19:06 PM »
I got a new barrel and hopup unit and its still only shooting upside down. I am having mag problems where the springs are getting stuck down in the mags but even the mags that I know are working because when I strip the mags, rounds fall out. I have no idea what I can do to fix my rifle or mags. Someone please help!!!!
And then my Magpul PTS Pmags springs are all stuck in the mags and I have no idea how to dissassemble them to fix them. Anyone know how too?

Pages: 1 [2] 3 4 ... 7